- Tim Holtz Distress Oxide Ink Pads : Spiced Marmalade, Fired Brick, Broken China
- Tim Holtz® Distress Ink Pads : Walnut Stain
- Tim Holtz® Distress Paint : Pumice Stone
- Tim Holtz® Distress Watercolor Cardstock
- Tim Holtz® Distress Splatter Brush
- Tim Holtz Distress® Grit-Paste
- Ranger Non-Stick Craft Sheet™
- Ranger Mini Blending Tool with Foam
- Ranger Heat it™ Craft Tool
- Tim Holtz® Distress Sprayer
- Palette Knife Set
- Ranger Paper Creasers
- Ranger Glossy Accents™
- Ranger Adhesive Foam Rolls : Black
- Tim Holtz by Tonic Studios Kushgrip Snips
- Tim Holtz Eclectic Elements Craft Thread
- Tim Holtz Idea-ology: Sanding Grip; Index Clip; Classic Kraft Paper Stash- Black Cardstock
- Tim Holtz Alterations by Sizzix Sentiment Words 661807 and Cityscape Commute 661809
- Tim Holtz Stampers Anonymous Dot Fade Layering Stencil THS006
Step 1: Working on a Non-Stick Craft Sheet swipe some Distress Oxide Spiced Marmalade. Spray droplets of water onto the ink using a Distress Sprayer bottle. Press or swipe a 4 1/4 x 5 1/2 sheet of Distress Watercolor Cardstock through the ink, picking up the color. While the Distress Watercolor Cardstock is still wet, slowly pull the trigger of the Distress Sprayer to add larger water droplets. Then dry with Heat It Tool. To add more Distress, pick up droplets of color off the Non-Stick Craft Sheet with the Distress Watercolor Cardstock, blotting to pick up the color (not swiping), then drying with Heat It Tool.
Step 2: Repeat the above steps to a second sheet of Distress Watercolor Cardstock using Fired Brick Distress Oxide.
Step 3: Squeeze a couple drops of Pumice Stone Distress Paint onto a Non-Stick Craft Sheet, and lightly mist the paint with water. Press the smooth side of the Distress Watercolor Cardstock into the paint mixture until covered. Dry with a Heat it Tool. To add more distress, pick up droplets of color off the Non-Stick Craft Sheet with Distress Watercolor Cardstock, blotting to pick up the color (not swiping), then drying with Heat Tool.
Step 4: Swipe some Distress Oxide Broken China onto the Non-Stick Craft Sheet. Spray droplets of water onto the ink using a Distress Spray bottle. Pick up color with Distress Splatter Brush for additional interest to colorized Spiced Marmalade Distress Watercolor Cardstock. Then dry with Heat It Tool.
Step 5: Place the Dot Fade Layering Stencil over the top of your colored Distress Watercolor Cardstock. I like to secure mine with washi or painters tape. Spread a thin layer of Distress Grit Paste sporadically through stencil. Carefully lift and remove layering stencil. Set Distress Watercolor Cardstock aside to air dry. Make sure to immediately clean your layering stencil and Ranger Pallet Knife right after use.
Step 6: Create a banner for card front from a 2×4 piece of Tim Holtz Classic Kraft – Black Cardstock. Cut a notch out of bottom. Die cut the word “best” in banner using Tim Holtz Sizzix Sentiment Words thin die set. Cut a 3.50×4.75 sheet of Tim Holtz Classic Kraft – Black Cardstock. Die Cut “Happy Father’s Day” using same die set as above.
Step 7: Die cut the base helicopter and the word “you” x2 (Sentiment Words) from Tim Holtz Classic Kraft – Black Cardstock. All helicopter parts are from Tim Holtz Sizzix Cityscape Commute die set. Die cut overlay helicopter blades from colored Pumice Stone Distress Watercolor Cardstock. Die cut the helicopter body and the word “dad” x2 from Fired Brick Distress Watercolor Cardstock. Save all those extra pieces for a future project.
Step 8: Cut a piece of Tim Holtz Classic Kraft – Black Cardstock 5 1/2 x 8 1/2 and fold in half to create cardbase. Distress all black cardstock with sanding grip to expose the underlying kraft.
Step 9: Shade all paper pieces with Walnut Stain Distress Ink and Blending Tool with Foam around edges. Further distress paper edges with paper creaser. To create the X, cut the end of 2 Y’s and glue together with a little Glossy Accents.
Step 10: Glue helicopter body and blades to helicopter base with Glossy Accents. Adhere a few small pieces of Ranger Black Adhesive Foam to back of helicopter. Glue a small piece of Tim Holtz Eclectic Elements Craft Thread about 3/4 inch long to X using Glossy Accents the attach to back of helicopter.
Step 11: Adhere Ranger Black Adhesive Foam to back of banner and Happy Father’s Day insert. Attach banner to top left side of colorized Spiced Marmalade sheet. Then adhere to card base with Glossy Accents.
Step 12: Adhere “Dad” to banner using Glossy Accents. Attach helicopter and XO with Glossy Accents as well. Wrap a little Tim Holtz Eclectic Elements Craft Thread around an index clip and attach to top of banner.
Step 13: Last but not least, attach the “Happy Father’s Day” insert to inside of card.